Select Functions Names of Components/Switching the Mode Standard Mode : Time Mode Standard Mode : Traveltime Mode Standard Mode : Destination timer Mode Standard Mode : Alarm Mode Standard Mode : Chronograph Mode Standard Mode : Timer Mode Standard Mode : System monitor Mode Dive Plan Mode Scuba Log Mode Skin Log Mode Diving Mode Surface Mode Low power Mode Data Communication Functions

Mode Change flow

Using the Standard Mode : Using the Time Mode

This mode is the basic mode of this watch that displays the time and date.

A. Switching the Display

* The display switches between the Day Display and Location Display each time the upper leftbutton (C) is pressed once. * When the upper right button (B) is pressed once when either the Day Display or Location Display is displayed, the display changes to the Enlarged Display. Pressing the upper right button (B) again returns it to the original display.
* When the charge of the watch becomes low (when the charge level indicator indicates  ), the "Day Display" or "Enlarged Display" automatically change to the "Location Display" after about 3 minutes to indicate that the watch should be charged.

B. Setting the Time and Date

1.	The watch enters the correction state (display is flashing) when the upper left button (C) is pressed for at least 2 seconds and then released during any display of the time mode.
2.	The location on the display that is flashing changes in the order shown below each time the upper left button (C) is pressed once. The watch returns to the normal display when the upper left button (C) is pressed and then released in the contrast correction state.
3.	Correct the flashing item by pressing either the upper right button (B) or lower right button (A).
	* Pressing the upper right button (B) advances the display by one step at a time each time it is pressed, while pressing the lower right button (A) moves the display back by one step at a time each time it is pressed. (Pressing either button continuously causes the display to change rapidly.) * Refer to the section on "Locations Displayed by this Watch" for information on displayed locations. * The watch returns to 00 seconds when the upper right button (B) or lower right button (A) is pressed. (If the seconds are between 30 and 59 seconds at that time the minutes advance by 1.) * When the display is set to switching daylight savings time (ON or OFF is flashing) or switching the 12H/24H format, the display switches back and forth between the settings each time the lower right button (A) or upper right button (B) is pressed.
4.	Pressing and then releasing the lower left button (D) returns the watch to the normal display.

* The year can be set from 2000 to 2099. However, January 1, 2000 is designated as a special date for use by the hardware system of this watch. If the watch is attempted to be used for infrared or USB communication or is switched to the low power mode while set to this date, all the display elements on the watch are displayed and the watch returns to the initial setting (12:00 AM, January 1, 2003). Please do not set your watch to January 1, 2000. * Once the date has been set, it is not necessary to correct for leap years or the end of the month. (Dates such as February 30 that do not actually exist are not displayed even during correction.) * Pay attention to AM (A) and PM (P) when using the 12 hour format. * When daylight savings time has been set (ON), the time advances by 1 hour from the current time and "ST" appears on the display. Daylight savings time cannot be set for Coordinated Universal Time (UTC). * The day is corrected automatically by correcting the year, month and date. * The watch automatically returns to the normal display when none of the buttons are pressed for about 3 minutes in the correction state (display flashing). * The watch can be immediately returned to the normal display by pressing the lower left button (D) and then releasing in the correction state (display flashing).

C. Daily Graphic Display
A single daily graphic is pre-registered in your watch at the time of purchase. Images displayed for the daily graphic can be changed, added or deleted by using the "CAPgm" software provided. Images registered for the daily graphic are displayed in order each day in the lower right corner of the "Day Display". In addition, on those days that have been set as anniversaries, the daily graphic registered for that anniversary is displayed.
Please refer to the "CAPgm" manual contained in the CD-ROM for further details regarding the procedures for setting and displaying daily graphics.

---

To Page-Top

Copyright 2003 CITIZEN WATCH CO.,LTD. ALL Rights Reserved.