Standard Mode : Destination timer Mode

Mode Change Flow

Using the Standard Mode : Using the Destination Timer Mode

The destination timer measures and displays the amount of time remaining until arriving at a destination up to a maximum of 99 hours, 59 minutes and 59 seconds after having set the destination and arrival time when traveling or on business overseas. Once the arrival time is reached, an alarm informing you of arrival sounds for about 30 seconds and "Dest" is displayed on the display. After arrival, elapsed time from the time of arrival is measured for up to 99 hours, 59 minutes and 59 seconds. In addition, the alarm informing you of arrival at your destination can be selected from 15 types of alarm sounds.

A. Setting the Destination Timer

The watch switches to the correction state (display flashes) when the upper left button (C) is pressed for at least 2 seconds and then released in the destination timer mode.

The flashing item changes in the order shown below each time the upper left button (C) is pressed once.

Pressing the upper left button (C) and then releasing in the alarm number correction state returns the watch to the normal display.

The flashing item can be corrected by pressing either the upper right button (B) or lower right button (A).

*	Pressing the upper right button (B) advances the display by one step at a time each time it is pressed, while pressing the lower right button (A) moves the display back by one step at a time each time it is pressed. (Pressing either button continuously causes the display to change rapidly.)
*	Refer to the section on "Locations Displayed by this Watch" for information on displayed locations.
*	When switching daylight savings time (ON or OFF is flashing), the display switches back and forth between the settings each time the lower right button (A) or upper right button (B) is pressed once.
*	When the upper right button (B) is pressed once while in the alarm number selection state (an alarm number is flashing), the next alarm number is called up each time it is pressed. When the lower right button (A) is pressed once in the alarm number selection state, the next alarm number is called up in the reverse order each time it is pressed. Select "Silent" when you do not want the alarm to sound.
*	You can monitor the alarm corresponding to the flashing alarm number by pressing the upper right button (B) or lower right button (A) in the alarm number selection state for as long as the button is pressed. (The next or previous alarm number is momentarily displayed the instant the button is pressed, while pressing either button continuously causes the set alarm to sound.)

Pressing the lower left button (D) and then releasing finalizes the setting after which the destination timer starts to run and the remaining time until the arrival time is displayed.

*	The 12 hour or 24 hour format setting is in accordance with the setting in the time mode.
*	In the case the remaining time until the set arrival time exceeds 100 hours, the destination timer stops at the arrival time display and then starts running automatically when the remaining time until the arrival time is within 99 hours, 59 minutes and 59 seconds.
*	When the arrival time has been set going back more than 100 hours, the destination timer stops at the arrival time display.
*	In the case of correcting the arrival time while the destination timer is running, the destination timer starts running according to the newly set arrival time.
*	The remaining time is recalculated in the case the time or daylight savings time setting is corrected for the location set with the destination timer in the time mode or travel time mode while the destination timer is running.
*	The watch automatically returns to the arrival time display or remaining time display when noneof the buttons are pressed for about 3 minutes in the correction state (display flashing).
*	The watch can be immediately returned to the arrival time display or remaining time display by pressing the lower left button (D) and then releasing in the correction state (display flashing).

B. Destination Timer Measuring Procedure

Once the destination timer has been set, measurement begins automatically. Once the timer reaches the arrival time, an alarm sounds for about 30 seconds informing you that the time is up. After the time on the destination timer is up, elapsed time from the arrival time flashes on the display for up to 99 hours, 59 minutes and 59 seconds. After this time has elapsed, the watch returns to the arrival time display.

*	The alarm that sounds when the arrival time is reached can be turned off by pressing any button.
*	If the alarm to inform of arrival is set to "Silent", arrival time is notified only with the "Dest" display on the display.

<Displaying Arrival Time Set during Measurement>

1.	When the upper right button (B) is pressed once while the destination timer is running, the set arrival time (destination location and time) is displayed.
2.	When the upper right button (B) is pressed once again while the arrival time is displayed, the time and location of the location selected in the time mode for the set arrival time are displayed.
3.	Pressing the upper right button (B) once again returns the watch to the remaining time display.

*	The watch automatically returns to the remaining time display when none of the buttons are pressed for about 3 minutes during the arrival time confirmation displays described in steps (1) and (2) above.
*	The watch automatically returns to the time mode when none of the buttons are pressed for about 3 minutes in the destination timer mode (including when the destination timer is running). Time up Elapsed time from arrival time.

To Page-Top